12 Chapter Review

Key Terms

breaking stress (ultimate stress)
value of stress at the fracture point
bulk modulus
elastic modulus for the bulk stress
bulk strain
(or volume strain) strain under the bulk stress, given as fractional change in volume
bulk stress
(or volume stress) stress caused by compressive forces, in all directions
center of gravity
point where the weight vector is attached
compressibility
reciprocal of the bulk modulus
compressive strain
strain that occurs when forces are contracting an object, causing its shortening
compressive stress
stress caused by compressive forces, only in one direction
elastic
object that comes back to its original size and shape when the load is no longer present
elastic limit
stress value beyond which material no longer behaves elastically and becomes permanently deformed
elastic modulus
proportionality constant in linear relation between stress and strain, in SI pascals
equilibrium
body is in equilibrium when its linear and angular accelerations are both zero relative to an inertial frame of reference
first equilibrium condition
expresses translational equilibrium; all external forces acting on the body balance out and their vector sum is zero
gravitational torque
torque on the body caused by its weight; it occurs when the center of gravity of the body is not located on the axis of rotation
linearity limit (proportionality limit)
largest stress value beyond which stress is no longer proportional to strain
normal pressure
pressure of one atmosphere, serves as a reference level for pressure
pascal (Pa)
SI unit of stress, SI unit of pressure
plastic behavior
material deforms irreversibly, does not go back to its original shape and size when load is removed and stress vanishes
pressure
force pressing in normal direction on a surface per the surface area, the bulk stress in fluids
second equilibrium condition
expresses rotational equilibrium; all torques due to external forces acting on the body balance out and their vector sum is zero
shear modulus
elastic modulus for shear stress
shear strain
strain caused by shear stress
shear stress
stress caused by shearing forces
static equilibrium
body is in static equilibrium when it is at rest in our selected inertial frame of reference
strain
dimensionless quantity that gives the amount of deformation of an object or medium under stress
stress
quantity that contains information about the magnitude of force causing deformation, defined as force per unit area
stress-strain diagram
graph showing the relationship between stress and strain, characteristic of a material
tensile strain
strain under tensile stress, given as fractional change in length, which occurs when forces are stretching an object, causing its elongation
tensile stress
stress caused by tensile forces, only in one direction, which occurs when forces are stretching an object, causing its elongation
Young’s modulus
elastic modulus for tensile or compressive stress

Key Equations

First Equilibrium Condition ∑kF⃗ k=0⃗ ∑kF→k=0→
Second Equilibrium Condition ∑kτ⃗ k=0⃗ ∑kτ→k=0→
Linear relation between

stress and strain

 stress=(elastic modulus)×strainstress=(elastic modulus)×strain
Young’s modulus Y=tensile stresstensile strain=F⊥AL0ΔLY=tensile stresstensile strain=F⊥AL0ΔL
Bulk modulus B=bulk stressbulk strain=−ΔpV0ΔVB=bulk stressbulk strain=−ΔpV0ΔV
Shear modulus S=shear stressshear strain=F∥AL0ΔxS=shear stressshear strain=F∥AL0Δx

Summary

12.1 Conditions for Static Equilibrium

  • A body is in equilibrium when it remains either in uniform motion (both translational and rotational) or at rest. When a body in a selected inertial frame of reference neither rotates nor moves in translational motion, we say the body is in static equilibrium in this frame of reference.
  • Conditions for equilibrium require that the sum of all external forces acting on the body is zero (first condition of equilibrium), and the sum of all external torques from external forces is zero (second condition of equilibrium). These two conditions must be simultaneously satisfied in equilibrium. If one of them is not satisfied, the body is not in equilibrium.
  • The free-body diagram for a body is a useful tool that allows us to count correctly all contributions from all external forces and torques acting on the body. Free-body diagrams for the equilibrium of an extended rigid body must indicate a pivot point and lever arms of acting forces with respect to the pivot.

12.2 Examples of Static Equilibrium

  • A variety of engineering problems can be solved by applying equilibrium conditions for rigid bodies.
  • In applications, identify all forces that act on a rigid body and note their lever arms in rotation about a chosen rotation axis. Construct a free-body diagram for the body. Net external forces and torques can be clearly identified from a correctly constructed free-body diagram. In this way, you can set up the first equilibrium condition for forces and the second equilibrium condition for torques.
  • In setting up equilibrium conditions, we are free to adopt any inertial frame of reference and any position of the pivot point. All choices lead to one answer. However, some choices can make the process of finding the solution unduly complicated. We reach the same answer no matter what choices we make. The only way to master this skill is to practice.

12.3 Stress, Strain, and Elastic Modulus

  • External forces on an object (or medium) cause its deformation, which is a change in its size and shape. The strength of the forces that cause deformation is expressed by stress, which in SI units is measured in the unit of pressure (pascal). The extent of deformation under stress is expressed by strain, which is dimensionless.
  • For a small stress, the relation between stress and strain is linear. The elastic modulus is the proportionality constant in this linear relation.
  • Tensile (or compressive) strain is the response of an object or medium to tensile (or compressive) stress. Here, the elastic modulus is called Young’s modulus. Tensile (or compressive) stress causes elongation (or shortening) of the object or medium and is due to an external forces acting along only one direction perpendicular to the cross-section.
  • Bulk strain is the response of an object or medium to bulk stress. Here, the elastic modulus is called the bulk modulus. Bulk stress causes a change in the volume of the object or medium and is caused by forces acting on the body from all directions, perpendicular to its surface. Compressibility of an object or medium is the reciprocal of its bulk modulus.
  • Shear strain is the deformation of an object or medium under shear stress. The shear modulus is the elastic modulus in this case. Shear stress is caused by forces acting along the object’s two parallel surfaces.

12.4 Elasticity and Plasticity

  • An object or material is elastic if it comes back to its original shape and size when the stress vanishes. In elastic deformations with stress values lower than the proportionality limit, stress is proportional to strain. When stress goes beyond the proportionality limit, the deformation is still elastic but nonlinear up to the elasticity limit.
  • An object or material has plastic behavior when stress is larger than the elastic limit. In the plastic region, the object or material does not come back to its original size or shape when stress vanishes but acquires a permanent deformation. Plastic behavior ends at the breaking point.

Conceptual Questions

12.1 Conditions for Static Equilibrium

1.

What can you say about the velocity of a moving body that is in dynamic equilibrium?

2.

Under what conditions can a rotating body be in equilibrium? Give an example.

3.

What three factors affect the torque created by a force relative to a specific pivot point?

4.

Mechanics sometimes put a length of pipe over the handle of a wrench when trying to remove a very tight bolt. How does this help?

For the next four problems, evaluate the statement as either true or false and explain your answer.

5.

If there is only one external force (or torque) acting on an object, it cannot be in equilibrium.

6.

If an object is in equilibrium there must be an even number of forces acting on it.

7.

If an odd number of forces act on an object, the object cannot be in equilibrium.

8.

A body moving in a circle with a constant speed is in rotational equilibrium.

9.

What purpose is served by a long and flexible pole carried by wire-walkers?

12.2 Examples of Static Equilibrium

10.

Is it possible to rest a ladder against a rough wall when the floor is frictionless?

11.

Show how a spring scale and a simple fulcrum can be used to weigh an object whose weight is larger than the maximum reading on the scale.

12.

A painter climbs a ladder. Is the ladder more likely to slip when the painter is near the bottom or near the top?

12.3 Stress, Strain, and Elastic Modulus

Note: Unless stated otherwise, the weights of the wires, rods, and other elements are assumed to be negligible. Elastic moduli of selected materials are given in Table 12.1.

13.

Why can a squirrel jump from a tree branch to the ground and run away undamaged, while a human could break a bone in such a fall?

14.

When a glass bottle full of vinegar warms up, both the vinegar and the glass expand, but the vinegar expands significantly more with temperature than does the glass. The bottle will break if it is filled up to its very tight cap. Explain why and how a pocket of air above the vinegar prevents the bottle from breaking.

15.

A thin wire strung between two nails in the wall is used to support a large picture. Is the wire likely to snap if it is strung tightly or if it is strung so that it sags considerably?

16.

Review the relationship between stress and strain. Can you find any similarities between the two quantities?

17.

What type of stress are you applying when you press on the ends of a wooden rod? When you pull on its ends?

18.

Can compressive stress be applied to a rubber band?

19.

Can Young’s modulus have a negative value? What about the bulk modulus?

20.

If a hypothetical material has a negative bulk modulus, what happens when you squeeze a piece of it?

21.

Discuss how you might measure the bulk modulus of a liquid.

12.4 Elasticity and Plasticity

Note: Unless stated otherwise, the weights of the wires, rods, and other elements are assumed to be negligible. Elastic moduli of selected materials are given in Table 12.1.

22.

What is meant when a fishing line is designated as “a 10-lb test?”

23.

Steel rods are commonly placed in concrete before it sets. What is the purpose of these rods?

Problems

12.1 Conditions for Static Equilibrium

24.

When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of 0.140 m from the center of the bolt. How much torque are you exerting relative to the center of the bolt?

25.

When opening a door, you push on it perpendicularly with a force of 55.0 N at a distance of 0.850 m from the hinges. What torque are you exerting relative to the hinges?

26.

Find the magnitude of the tension in each supporting cable shown below. In each case, the weight of the suspended body is 100.0 N and the masses of the cables are negligible.

Figure A shows small pan of mass supported by string T3 that is tied to strings T1 and T2. Strings T1 and T2 are connected to two beams intersecting at a 90 degree angle. String T1 is perpendicular to the beam it is connected to. String T2 forms a 45 degree angle with the beam it is connected to. Figure B shows small pan of mass supported by string T2 that is tied to two identical strings T1. Strings T1 form 60 degree angles with the beam they are connected to. Figure C shows small pan of mass supported by string T3 that is tied to strings T1 and T2. String T1 and T2 form 60 and 45 degree angles, respectively, with the beam they are connected to. Figure D shows small pan of mass supported by string T4 that is tied to two strings T3 forming 6o degrees angle with the string T2. String T2 is connected to the beam by two strings T1. Strings T1 form 45 degree angles with the beam.

27.

What force must be applied at point P to keep the structure shown in equilibrium? The weight of the structure is negligible.

Figure shows the distribution of forces applied to point P. Force of 2000 N, two meters to the left of the point P, moves it downwards. Force of 4000 N, two meters to the right and one meter above of the point P, moves it to the right.

28.

Is it possible to apply a force at P to keep in equilibrium the structure shown? The weight of the structure is negligible.

Figure shows the distribution of forces applied to point P. Force of 2000 N, two meters to the left of the point P, moves it downwards. Force of 3000 N, two meters to the right of the point P, moves it upwards. Force of 5000 N, two meters to the right and one meter above of the point P, moves it to the right.

29.

Two children push on opposite sides of a door during play. Both push horizontally and perpendicular to the door. One child pushes with a force of 17.5 N at a distance of 0.600 m from the hinges, and the second child pushes at a distance of 0.450 m. What force must the second child exert to keep the door from moving? Assume friction is negligible.

30.

A small 1000-kg SUV has a wheel base of 3.0 m. If 60% if its weight rests on the front wheels, how far behind the front wheels is the wagon’s center of mass?

31.

The uniform seesaw is balanced at its center of mass, as seen below. The smaller boy on the right has a mass of 40.0 kg. What is the mass of his friend?

Figure is a schematic drawing of two boys on the seesaw. One boy sits two meters from the edge of the seesaw and two meters from the center. Another boys sits at the opposite edge of the seesaw, four meters from the center.

12.2 Examples of Static Equilibrium

32.

A uniform plank rests on a level surface as shown below. The plank has a mass of 30 kg and is 6.0 m long. How much mass can be placed at its right end before it tips? (Hint: When the board is about to tip over, it makes contact with the surface only along the edge that becomes a momentary axis of rotation.)

Figure schematic drawing of uniform plank rests on a level surface. Part of the plank that is 4.2 meters long is supported by the plank. Part of the plank that is 1.8 meters long is hanging over it.

33.

The uniform seesaw shown below is balanced on a fulcrum located 3.0 m from the left end. The smaller boy on the right has a mass of 40 kg and the bigger boy on the left has a mass 80 kg. What is the mass of the board?

Figure is a schematic drawing of two boys on the seesaw. One boy sits on the edge of the seesaw three meters from the center. Another boys sits at the opposite edge of the seesaw, five meters from the center.

34.

In order to get his car out of the mud, a man ties one end of a rope to the front bumper and the other end to a tree 15 m away, as shown below. He then pulls on the center of the rope with a force of 400 N, which causes its center to be displaced 0.30 m, as shown. What is the force of the rope on the car?

Figure is a schematic drawing that shows a rope tied to the front bumper and the other end to a tree 15 m away. A force of 400 N is applied to the center of the rope and causes it to get displaced 0.30 m.

35.

A uniform 40.0-kg scaffold of length 6.0 m is supported by two light cables, as shown below. An 80.0-kg painter stands 1.0 m from the left end of the scaffold, and his painting equipment is 1.5 m from the right end. If the tension in the left cable is twice that in the right cable, find the tensions in the cables and the mass of the equipment.

Figure is a schematic drawing of a man standing at the left side and the bucket placed at the right side of a scaffold.

36.

When the structure shown below is supported at point P, it is in equilibrium. Find the magnitude of force F and the force applied at P. The weight of the structure is negligible.

Figure shows the distribution of forces applied to point P. Force of 2000 N, two meters to the left of the point P, moves it downwards. Force F, two meters to the left and two meters above of the point P, moves it to the right. Force of 1000 N, two meters to the right and three meters below of the point P, moves it to the left.

37.

To get up on the roof, a person (mass 70.0 kg) places a 6.00-m aluminum ladder (mass 10.0 kg) against the house on a concrete pad with the base of the ladder 2.00 m from the house. The ladder rests against a plastic rain gutter, which we can assume to be frictionless. The center of mass of the ladder is 2.00 m from the bottom. The person is standing 3.00 m from the bottom. Find the normal reaction and friction forces on the ladder at its base.

38.

A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support at the wall, and the other end of the strut is attached to a sign that weighs 200.0 N. The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the strut, find the tension in the cable and the force at the hinge of the strut.

Figure is a schematic drawing of a sign which hangs from the end of a uniform strut. The strut forms a 30 degree angle with the cable tied to the wall above the left end of the strut.

39.

The forearm shown below is positioned at an angle θθ with respect to the upper arm, and a 5.0-kg mass is held in the hand. The total mass of the forearm and hand is 3.0 kg, and their center of mass is 15.0 cm from the elbow. (a) What is the magnitude of the force that the biceps muscle exerts on the forearm for θ=60°?θ=60°? (b) What is the magnitude of the force on the elbow joint for the same angle? (c) How do these forces depend on the angle θ?θ?

Figure is a schematic drawing of a forearm rotated around the elbow. A 5 kilogram ball is held in the palm. The distance between the elbow and the ball is 35 centimeters. The distance between the elbow and the biceps muscle, which causes a torque around the elbow, is 4 centimeters. Forearm forms a theta angle with the upper arm.

40.

The uniform boom shown below weighs 3000 N. It is supported by the horizontal guy wire and by the hinged support at point A. What are the forces on the boom due to the wire and due to the support at A? Does the force at A act along the boom?

Figure is a schematic drawing of a 2000 N weight that is supported by the horizontal guy wire and by the hinged support at point A. Hinged support forms a 45 degree angle with the ground.

41.

The uniform boom shown below weighs 700 N, and the object hanging from its right end weighs 400 N. The boom is supported by a light cable and by a hinge at the wall. Calculate the tension in the cable and the force on the hinge on the boom. Does the force on the hinge act along the boom?

Figure is a schematic drawing of a 400 N weight that is by a cable and by a hinge at the wall. Hinge forms a 20 degree angle with the line perpendicular to the wall. Cable forms a 45 degree angle with the line perpendicular to the wall.

42.

A 12.0-m boom, AB, of a crane lifting a 3000-kg load is shown below. The center of mass of the boom is at its geometric center, and the mass of the boom is 1000 kg. For the position shown, calculate tension T in the cable and the force at the axleA.

Figure is a schematic drawing of a crane lifting a 3000-kg load. Arm of a crane forms a 30 degree angle with the line parallel to the ground. Cable supporting load forms a 10 degree angle with the arm.

43.

A uniform trapdoor shown below is 1.0 m by 1.5 m and weighs 300 N. It is supported by a single hinge (H), and by a light rope tied between the middle of the door and the floor. The door is held at the position shown, where its slab makes a 30°30°angle with the horizontal floor and the rope makes a 20°20° angle with the floor. Find the tension in the rope and the force at the hinge.

Figure is a schematic drawing of a trapdoor that is 1.0 m by 1.5 m. Door is supported by a single hinge labeled H, and by a light rope tied between the middle of the door and the floor. The door makes a 30 degree angle with the floor and the rope makes a 20 degree angle with the floor.

44.

A 90-kg man walks on a sawhorse, as shown below. The sawhorse is 2.0 m long and 1.0 m high, and its mass is 25.0 kg. Calculate the normal reaction force on each leg at the contact point with the floor when the man is 0.5 m from the far end of the sawhorse. (Hint: At each end, find the total reaction force first. This reaction force is the vector sum of two reaction forces, each acting along one leg. The normal reaction force at the contact point with the floor is the normal (with respect to the floor) component of this force.)

Figure is a schematic drawing of a man walks on a sawhorse. Each side of the sawhorse is supported by two connected legs. There are 60 degree angles between the legs.

12.3 Stress, Strain, and Elastic Modulus

45.

The “lead” in pencils is a graphite composition with a Young’s modulus of approximately 1.0×109N/m2.1.0×109N/m2. Calculate the change in length of the lead in an automatic pencil if you tap it straight into the pencil with a force of 4.0 N. The lead is 0.50 mm in diameter and 60 mm long.

46.

TV broadcast antennas are the tallest artificial structures on Earth. In 1987, a 72.0-kg physicist placed himself and 400 kg of equipment at the top of a 610-m-high antenna to perform gravity experiments. By how much was the antenna compressed, if we consider it to be equivalent to a steel cylinder 0.150 m in radius?

47.

By how much does a 65.0-kg mountain climber stretch her 0.800-cm diameter nylon rope when she hangs 35.0 m below a rock outcropping? (For nylon, Y=1.35×109Pa.)Y=1.35×109Pa.)

48.

When water freezes, its volume increases by 9.05%. What force per unit area is water capable of exerting on a container when it freezes?

49.

A farmer making grape juice fills a glass bottle to the brim and caps it tightly. The juice expands more than the glass when it warms up, in such a way that the volume increases by 0.2%. Calculate the force exerted by the juice per square centimeter if its bulk modulus is 1.8×109N/m2,1.8×109N/m2, assuming the bottle does not break.

50.

A disk between vertebrae in the spine is subjected to a shearing force of 600.0 N. Find its shear deformation, using the shear modulus of 1.0×109N/m2.1.0×109N/m2. The disk is equivalent to a solid cylinder 0.700 cm high and 4.00 cm in diameter.

51.

A vertebra is subjected to a shearing force of 500.0 N. Find the shear deformation, taking the vertebra to be a cylinder 3.00 cm high and 4.00 cm in diameter. How does your result compare with the result obtained in the preceding problem? Are spinal problems more common in disks than in vertebrae?

52.

Calculate the force a piano tuner applies to stretch a steel piano wire by 8.00 mm, if the wire is originally 1.35 m long and its diameter is 0.850 mm.

53.

A 20.0-m-tall hollow aluminum flagpole is equivalent in strength to a solid cylinder 4.00 cm in diameter. A strong wind bends the pole as much as a horizontal 900.0-N force on the top would do. How far to the side does the top of the pole flex?

54.

A copper wire of diameter 1.0 cm stretches 1.0% when it is used to lift a load upward with an acceleration of 2.0m/s2.2.0m/s2.What is the weight of the load?

55.

As an oil well is drilled, each new section of drill pipe supports its own weight and the weight of the pipe and the drill bit beneath it. Calculate the stretch in a new 6.00-m-long steel pipe that supports a 100-kg drill bit and a 3.00-km length of pipe with a linear mass density of 20.0 kg/m. Treat the pipe as a solid cylinder with a 5.00-cm diameter.

56.

A large uniform cylindrical steel rod of density ρ=7.8g/cm3ρ=7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. The rod is fastened to a concrete floor with its long axis vertical. What is the normal stress in the rod at the cross-section located at (a) 1.0 m from its lower end? (b) 1.5 m from the lower end?

57.

A 90-kg mountain climber hangs from a nylon rope and stretches it by 25.0 cm. If the rope was originally 30.0 m long and its diameter is 1.0 cm, what is Young’s modulus for the nylon?

58.

A suspender rod of a suspension bridge is 25.0 m long. If the rod is made of steel, what must its diameter be so that it does not stretch more than 1.0 cm when a 2.5×104-kg2.5×104-kg truck passes by it? Assume that the rod supports all of the weight of the truck.

59.

A copper wire is 1.0 m long and its diameter is 1.0 mm. If the wire hangs vertically, how much weight must be added to its free end in order to stretch it 3.0 mm?

60.

A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and 2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?

61.

The bulk modulus of a material is 1.0×1011N/m2.1.0×1011N/m2. What fractional change in volume does a piece of this material undergo when it is subjected to a bulk stress increase of 107N/m2?107N/m2? Assume that the force is applied uniformly over the surface.

62.

Normal forces of magnitude 1.0×106N1.0×106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?

63.

During a walk on a rope, a tightrope walker creates a tension of 3.94×103N3.94×103N in a wire that is stretched between two supporting poles that are 15.0 m apart. The wire has a diameter of 0.50 cm when it is not stretched. When the walker is on the wire in the middle between the poles the wire makes an angle of 5.0°5.0° below the horizontal. How much does this tension stretch the steel wire when the walker is this position?

64.

When using a pencil eraser, you exert a vertical force of 6.00 N at a distance of 2.00 cm from the hardwood-eraser joint. The pencil is 6.00 mm in diameter and is held at an angle of 20.0°20.0° to the horizontal. (a) By how much does the wood flex perpendicular to its length? (b) How much is it compressed lengthwise?

65.

Normal forces are applied uniformly over the surface of a spherical volume of water whose radius is 20.0 cm. If the pressure on the surface is increased by 200 MPa, by how much does the radius of the sphere decrease?

12.4 Elasticity and Plasticity

66.

A uniform rope of cross-sectional area 0.50cm20.50cm2 breaks when the tensile stress in it reaches 6.00×106N/m2.6.00×106N/m2. (a) What is the maximum load that can be lifted slowly at a constant speed by the rope? (b) What is the maximum load that can be lifted by the rope with an acceleration of 4.00m/s2?4.00m/s2?

67.

One end of a vertical metallic wire of length 2.0 m and diameter 1.0 mm is attached to a ceiling, and the other end is attached to a 5.0-N weight pan, as shown below. The position of the pointer before the pan is 4.000 cm. Different weights are then added to the pan area, and the position of the pointer is recorded in the table shown. Plot stress versus strain for this wire, then use the resulting curve to determine Young’s modulus and the proportionality limit of the metal. What metal is this most likely to be?

Added load (including pan)

(N)

 Scale reading

(cm)
0 4.000
15 4.036
25 4.073
35 4.109
45 4.146
55 4.181
65 4.221
75 4.266
85 4.316

Figure shows vertical wire attached to a ceiling with the other end is attached to a weight pan.

68.

An aluminum (ρ=2.7g/cm3)(ρ=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0×107N/m2?8.0×107N/m2?

Additional Problems

69.

The coefficient of static friction between the rubber eraser of the pencil and the tabletop is μs=0.80.μs=0.80. If the force F⃗ F→ is applied along the axis of the pencil, as shown below, what is the minimum angle at which the pencil can stand without slipping? Ignore the weight of the pencil.

Figure shows a pencil that rests against a corner. The eraser end touches a rough horizontal floor. Angle between pencil and ground is Theta.

70.

A pencil rests against a corner, as shown below. The sharpened end of the pencil touches a smooth vertical surface and the eraser end touches a rough horizontal floor. The coefficient of static friction between the eraser and the floor is μs=0.80.μs=0.80.The center of mass of the pencil is located 9.0 cm from the tip of the eraser and 11.0 cm from the tip of the pencil lead. Find the minimum angle θθ for which the pencil does not slip.

Figure shows a pencil that rests against a corner. The sharpened end of the pencil touches a smooth vertical surface and the eraser end touches a rough horizontal floor. Angle between pencil and ground is Theta. Center of mass is 9 cm from the eraser and 11 cm from the sharpened end.

71.

A uniform 4.0-m plank weighing 200.0 N rests against the corner of a wall, as shown below. There is no friction at the point where the plank meets the corner. (a) Find the forces that the corner and the floor exert on the plank. (b) What is the minimum coefficient of static friction between the floor and the plank to prevent the plank from slipping?

Figure shows a uniform plank that rests against a corner the corner of a wall. Part of the plank from the floor to the corner of the wall is 3.0 m long, 1.0 m long part of plank is above the wall. Distance between the part of the plank that touches the ground and the corner of the wall is 1.5 m.

72.

A 40-kg boy jumps from a height of 3.0 m, lands on one foot and comes to rest in 0.10 s after he hits the ground. Assume that he comes to rest with a constant deceleration. If the total cross-sectional area of the bones in his legs just above his ankles is 3.0cm2,3.0cm2, what is the compression stress in these bones? Leg bones can be fractured when they are subjected to stress greater than 1.7×108Pa.1.7×108Pa. Is the boy in danger of breaking his leg?

73.

Two thin rods, one made of steel and the other of aluminum, are joined end to end. Each rod is 2.0 m long and has cross-sectional area 9.1mm2.9.1mm2. If a 10,000-N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.

74.

Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15 mm under some stress, how much does the steel rod stretch under the same stress?

Challenge Problems

75.

A horizontal force F⃗ F→ is applied to a uniform sphere in direction exact toward the center of the sphere, as shown below. Find the magnitude of this force so that the sphere remains in static equilibrium. What is the frictional force of the incline on the sphere?

Figure shows a sphere of radius R and mass M that placed at the side of the triangle forming angle Theta with the ground. Force F is applied to the sphere.

76.

When a motor is set on a pivoted mount seen below, its weight can be used to maintain tension in the drive belt. When the motor is not running the tensions T1T1 and T2T2 are equal. The total mass of the platform and the motor is 100.0 kg, and the diameter of the drive belt pulley is 16.0cm.16.0cm. when the motor is off, find: (a) the tension in the belt, and (b) the force at the hinged platform support at point C. Assume that the center of mass of the motor plus platform is at the center of the motor.

Figure shows a motor set on a pivoted mount. The center of the motor is 25 cm above and 30 cm to the right from the support point C. Tension T1 forms a 40 degree angle with the line parallel to the ground. Tension T2 forms a 15 degree angle with the line parallel to the ground.

77.

Two wheels A and B with weights w and 2w, respectively, are connected by a uniform rod with weight w/2, as shown below. The wheels are free to roll on the sloped surfaces. Determine the angle that the rod forms with the horizontal when the system is in equilibrium. Hint: There are five forces acting on the rod, which is two weights of the wheels, two normal reaction forces at points where the wheels make contacts with the wedge, and the weight of the rod.

Figure shows the wheels A and B connected by the rod and located at the opposite side of the right angle triangle. Side at which wheel A is located forms a 60 degree angle with the line parallel to the ground. Side at which wheel B is located forms a 30 degree angle with the line parallel to the ground.

78.

Weights are gradually added to a pan until a wheel of mass M and radius R is pulled over an obstacle of height d, as shown below. What is the minimum mass of the weights plus the pan needed to accomplish this?

Figure shows a pan connected to the wheel by a wire. Wire has mass M and radius R. An obstacle of height D separates wheel from the pan.

79.

In order to lift a shovelful of dirt, a gardener pushes downward on the end of the shovel and pulls upward at distance l2l2from the end, as shown below. The weight of the shovel is mg⃗ mg→ and acts at the point of application of F⃗ 2.F→2. Calculate the magnitudes of the forces F⃗ 1F→1 and F⃗ 2F→2 as functions of l1,l1, l2,l2, mg, and the weight W of the load. Why do your answers not depend on the angle θθ that the shovel makes with the horizontal?

Figure shows a gardener lifting a shovel full of ground with both hands. Force F1 is applied to the back hand. Force F2 is applied to front hand. Force w is applied to the front of shovel with ground. Distance between the back hand and front of shovel is l1. Distance between the back and front hands is l2. Angle between the shovel and line parallel to the ground is theta.

80.

A uniform rod of length 2R and mass M is attached to a small collar C and rests on a cylindrical surface of radius R, as shown below. If the collar can slide without friction along the vertical guide, find the angle θθ for which the rod is in static equilibrium.

Figure shows a uniform rod of length 2R and mass that M is attached to a small collar C and rests on a cylindrical surface of radius R. Angle between the collar and the line parallel to the ground is theta.

81.

The pole shown below is at a 90.0°90.0° bend in a power line and is therefore subjected to more shear force than poles in straight parts of the line. The tension in each line is 4.00×104N,4.00×104N, at the angles shown. The pole is 15.0 m tall, has an 18.0 cm diameter, and can be considered to have half the strength of hardwood. (a) Calculate the compression of the pole. (b) Find how much it bends and in what direction. (c) Find the tension in a guy wire used to keep the pole straight if it is attached to the top of the pole at an angle of 30.0°30.0° with the vertical. The guy wire is in the opposite direction of the bend.

Figure shows a pole to which two forces T and force Tgw are applied. There is a 90 degree angle between two T forces. There is an 80 degree angle between the plane T forces are applied anf the pole. There is a 30 degree angle between Tgw and the pole.